Product Specifications
2018-2024 Jeep Wrangler JL & 2020-2024 Gladiator JT 3.6L Cold Air Intake
Replace the factory intake tract with a bolt-on kit built around a 3-inch aluminum tube, dry reusable filter, and sealed heat shield. This Flashark cold air intake is designed for 2018-2024 Jeep Wrangler JL and 2020-2024 Gladiator JT models with the 3.6L Pentastar V6. Its powder-coated components and deeper induction tone give drivers a distinct configuration and sound under acceleration.
Specifications
| SKU | FLBQM0004006 |
|---|---|
| Brand | Flashark |
| Intake tube | 3 inches (76 mm), mandrel-bent aluminum; black powder-coated finish |
| Filter | Red, washable dry cotton gauze; no filter oil required |
| Heat shield | Black powder-coated steel with black edge trim |
| Connections | Silicone reducer couplers and stainless steel T-bolt clamps |
| Expected output range | Approximately 20-29 hp (7-10%) and 13-18 lb-ft (5-7%); results vary with altitude, fuel quality, vehicle condition, calibration, installation, and supporting hardware. |
| Typical installation | Approximately 30-45 minutes with a socket set, screwdriver, and pliers; bolt-on and reversible to stock. |
| Filter service | Inspect and clean approximately every 15,000-20,000 miles; inspect more often and clean approximately every 5,000-10,000 miles in dusty off-road use. |
| Warranty | 1 year |
| Support | service@flasharkracing.com |
Key Features
- Mandrel-bent aluminum tube: The smooth 3-inch tube replaces the factory corrugated intake tube; its black powder-coated finish is intended to resist under-hood heat and corrosion.
- Dry cotton gauze filter: The washable red element needs no oil, avoiding the oiling step and the related risk of oil reaching a sensor.
- Sealed heat shield: The black steel shield and edge trim are designed to isolate the filter from engine-bay heat and seal against the hood liner while drawing air from outside the engine bay.
- Expected power change: Approximately 20-29 hp (7-10%) is the published range based on a stock 285 hp Pentastar; results vary with vehicle and operating conditions, including on eTorque models.
- Expected torque change: Approximately 13-18 lb-ft (5-7%) is the published range based on stock 260 lb-ft output; the intended benefit includes low-to-mid-range response for trail driving and highway merging.
- Intake tone: Expect a deeper induction sound under acceleration, with a quieter character at idle and cruise; sound varies by vehicle and driving conditions.
- Reusable filter: The stated service interval is approximately 15,000-20,000 miles, or 5,000-10,000 miles in dusty off-road use, which can reduce disposable filter purchases and waste.
- Bolt-on package: Couplers, clamps, hardware, and instructions support a typical 30-45 minute installation with basic hand tools, without cutting or drilling, and allow a return to the stock configuration.
Who This Kit Is For
This kit is for the 3.6L Pentastar Wrangler JL or Gladiator JT owner who wants a dry, reusable filter, a powder-coated intake assembly, and a deeper induction note. For other Jeep intake configurations, browse the Jeep cold air intake kits collection.
Check Before Ordering
- Confirm your vehicle is a Wrangler JL or Gladiator JT with the 3.6L Pentastar V6. A 2018 Wrangler may be a JK or JL; check the vehicle designation before ordering.
- The fitment tab covers standard and eTorque configurations, 4WD, and specific trims. Confirm the exact trim and model year with Flashark support if your configuration differs from the fitment information.
- This kit is not for the 2.0L turbo I4, 3.0L EcoDiesel V6, 6.4L V8 Rubicon 392, or Wrangler JK. The JK requires a different intake kit.
- Confirm factory sensor and throttle-body connections before installation. Reuse the applicable factory sensor and check all couplers and clamps for a secure seal; a check engine light cannot be ruled out for every vehicle.
- Use the dry filter without oil and inspect it more often in dusty off-road conditions. Avoid deep water crossings because water ingestion can cause engine damage.
- Check the emissions rules where the vehicle is registered before ordering. Contact Flashark support for fitment or installation help.
What's in the Box
- 1 black powder-coated 3-inch aluminum intake tube
- 1 red dry cotton gauze cone filter
- 1 black powder-coated steel heat shield
- 1 black edge trim
- 2 silicone reducer couplers
- 4 stainless steel T-bolt clamps
- 1 installation hardware kit with bolts, washers, nuts, and brackets
- 1 installation instructions manual
Shipping & Returns
Free U.S. Shipping: Orders are typically processed within 1–2 business days and delivered within 7–9 business days. Additional charges may apply to remote areas.
30-Day Returns: Unopened and unused items in their original packaging may be returned within 30 days of receipt. Return shipping is covered for verified quality issues.
Worry-Free Delivery: Optional protection against eligible loss, theft, delay, or transit damage is available at checkout.
Compliance Notice
Not legal for sale or use in California (and other CARB-adopting states). This intake does not modify the vehicle's emissions components; confirm applicable street-use and inspection rules before ordering.
